ETI SV 216 disconnect switch 2-pole 16A
ETI SV 216 is a load break switch intended for manual switching of electrical circuits under load in low-voltage distribution systems. It is used for...
Кількість полюсів
2
Ступінь захисту IP
IP20
Ширина в кількості модульних відстаней
2
Струм короткого замикання Icw
6 kA
Струмова витривалість до ударного струму
0.25 kA
Номінальна напруга
230 V
Номінальна ізоляційна напруга Ui
500 V
Номінальний струм витоку
0.03 A
Code: CDA240D
Two-pole Hager CDA240D residual current device for 230 V AC networks, rated current 40 A, residual current 30 mA, Type A, DIN-rail mounted.
1,743.56 ₴
On Order
Delivery across Ukraine within 5 days from the purchase date.
Pay for orders via Liqpay and plata by mono services.
100% certified products. Service and support.
The Hager CDA240D residual current device is designed to protect electrical circuits in residential, commercial, and small industrial distribution boards. Its task is to disconnect the line when a differential current appears, which may indicate insulation damage or current leakage to the equipment housing. With two poles, the device is suitable for single-phase AC networks with a rated voltage of 230 V and a frequency of 50 Hz.
This model is rated for 40 A nominal current and a 30 mA residual current threshold, making it appropriate for protecting final circuits and individual loads where an elevated level of electrical safety is required. Type A residual current detection means the device responds not only to sinusoidal AC leakage current but also to pulsating DC residual current, which is important for modern household and office equipment with electronic components.
The device has a short-circuit current rating Icw of 6 kA and a surge withstand current of 0.25 kA. The rated insulation voltage Ui is 500 V, while the rated impulse withstand voltage Uimp reaches 4 kV. These parameters allow the unit to operate in systems exposed to typical impulse overvoltages found in distribution networks. The IP20 degree of protection and pollution degree 2 indicate installation inside an electrical enclosure under normal operating conditions.
Mounting is performed on a DIN rail. The housing takes 2 module widths, and the installation depth is 70 mm. Additional accessories can be installed, and the unit is equipped with a locking device. Connection is possible with solid conductors from 1 to 25 mm² and stranded conductors from 1 to 16 mm². The operating temperature range is from -25 to +40 °C. The enclosure color corresponds to RAL 7005.
Кількість полюсів
2
Ступінь захисту IP
IP20
Ширина в кількості модульних відстаней
2
Струм короткого замикання Icw
6 kA
Струмова витривалість до ударного струму
0.25 kA
Номінальна напруга
230 V
Номінальна ізоляційна напруга Ui
500 V
Номінальний струм витоку
0.03 A
Номінальний струм
40 A
Глибина вбудовування
70 mm
Номер RAL (аналогічний)
7005
Під`єднуваний переріз багатодротового провідника
1-16 mm²
Вибухозахищений
ні
Селективний захист
ні
Короткочасне затримане спрацьовування
ні
Можливе додаткове обладнання
так
Метод монтажу
DIN-рейка
З блокувальним пристроєм
так
Тип напруги
Змінний струм
Тип витоку струму
A
Частота
50 Гц
Номінальна напруга витримування удару Uimp
4 kV
Температура навколишнього середовища під час роботи
-25-40 °C
Під`єднуваний переріз твердого провідника
1-25 mm²
Power loss
6.24 W
0 reviews
No reviews for this product yet. Be the first!